Fallingwater Lamp

A few years ago I had the opportunity to visit Frank Lloyd Wright’s architectural masterpiece Fallingwater. The Kaufmann family, owners of a prosperous 1930s era Pittsburg, PA department store, commissioned Frank Lloyd Wright to build a vacation home on their property Southeast of the city. To learn more about this National Historic Landmark visit the Fallingwater web site.

Wright was well known to design not just the building, but the complete living environment for his clients, including furnishings. One of the accessories at Fallingwater which caught my attention was a bedside lamp, used in both the main house and guest house.

Over the 10 or so years since my visit to Fallingwater I have become an ardent fan of the architecture and design of Wright. By chance I discovered an article on the Popular Woodworking Magazine website entitled Fallingwater Table Lamp and I decided then and there to build one.

After comparing the Popular Woodworking version to original photos of the lamp were some differences, so I came up with my own plans, attempting to stick as close as possible to the original photos.

Fallingwater Bedside Lamp Plans (To download plans, right click and select Save Link As…)

The shade sides are walnut – I used a single wide piece of walnut and mitered it at the center of the flame pattern in the walnut so it wraps around the shade. The shade base is poplar painted black and I used small biscuits to attach the shade sides to the shade base. The lamp base is of the same poplar painted black.

Here are the differences between the Popular Woodworking (PW) plan and what I built:

The walnut shade on the PW plan is 2 pieces mitered giving a 2 sided “L” shape. The original had 4 pieces mitered so there are 2 more shorter “wing” pieces on the shade with the shade having 4 sides. Here is a view from the top:

The PW plan has the lamp shade base attached inside the shade sides so it is not visible from the front. The shade base is square. On the original the shade side sat on top of the shade base with the base extending about 3/16” beyond the shade sides. The original base is not square and has a more complicated shape:

The profile of the lamp base on the PW plan is thicker and more “blocky” looking where the original has a thinner profile. One last modification I made was to add a heat shield/reflector. Neither the original nor the PW version had a heat shield.


I made the heat shield out of  aluminum flashing from the home center. I used some small wood screws and washers to space the reflector out about 1/4” from the shade.


I cut the aluminum with a utility knife and straightedge.


I marked and taped where I wanted to make the bends. I clamped thin pieces of wood to both sides of the aluminum, placed the aluminum on the edge of the work bench and bent it.


The bend wasn’t real crisp so I took a piece of wood and “creased” the bend which did the trick.


Here’s an end view of the shield.


I made a template to mark where I wanted to put the screws.
I put a 1/4” spacer behind the shade and marked the points to drill with an awl.


Here’s a picture with the spacer sticking out the end.


I wanted to make sure I didn’t screw through the shade so I did a mock up with a piece of wood the same thickness of the shade.


Here’s the shield screwed in place. I had to remove the light socket and base to install the shield.


An end view showing the air space.


A picture with the lamp on. It reflects much more light now. Before the wood shade got pretty warm where the bulb was, now it stays cool.


The finished lamp.


If you enjoyed this post, subscribe and get updates by email

Enter your email address:

Delivered by FeedBurner

5 thoughts on “Fallingwater Lamp

  1. I am interested in purchasing lamps very similar to the ones in the Fallingwater House. Any ideas or recommendations as to where I could get them? Any info would help! Thank you!

  2. This is a great lamp, I’m looking forward to starting the project soon. I may go with a cherry shade although the walnut looks great. Thank you very much for the pics and detailed info…much appreciated!

Leave a Comment